When we shared that we were covering our old concrete walkway with $1 pavers from Lowe’s, you guys had LOTS of questions. We’re excited to share a full tutorial with aaaall the deets. Let’s dive in!
This post is sponsored by Lowe’s.
Our front walkway at The Vic left much to be desired…
A big part of the problem was our concrete walkway and stairs.
As a part of our curb appeal update this summer, we planned on jacking up all of the old concrete and replacing it with new concrete. The contractors we contacted were all booked and expensive, so we started thinking of other ideas. Would it be possible to just cover it with new pavers instead? After lots of research, the answer was yes! It’s possible, and totally doable, to cover old concrete with pavers. There’s just a few caveats:
#1: Your surface needs to be intact and solid. If you have a crumbling surface, this project won’t work without some extra prep work.
#2: Your surface needs to be relatively flat without any large cracks or bumps in it.
Our walkway was pretty solid with the exception of two cracks about 1/2″ high, which we knew we could fix with proper prep. We grabbed a few $1 concrete pavers from Lowe’s and placed them in a diamond pattern to see if we liked the way they looked.
We LOVED the impact the pattern had on our curb appeal and decided to give it a shot. Here’s what we did:
STEP 1: Gather all TOOLS AND MATERIALS needed
To get this project done, we used the following materials:
- Pavers – we used basic $1 concrete pavers from Lowe’s (ours were on sale, but they’re normally priced between $1-2)
- Spacers – we used plastic paver spikes as spacers, and then reused them for our paver edging when we were finished
- Paver edging – this holds pavers in place and prevents them from shifting
- Landscaping cloth (and weed killer, if you need it) – to prevent weeds from growing through cracks after pavers are installed
- Leveling paver sand – this helps level any surface unevenness under the pavers
- Polymeric sand – a special kind of sand that helps adheres sand in place
- A broom – to spread polymeric sand after pavers are in place
- A circular saw for making straight paver cuts (if you prefer corded, this one has great reviews too!)
- A grinder for making curved paver cuts (we used this cordless Kobalt one)
- Diamond tip saw blades
STEP 2: dry run
Before we started actually laying our pavers and making cuts, we did a dry run to figure out our center line, correct spacing, etc. This allowed us to shift pavers and make adjustments quickly and easily before committing. In our case, we wanted our diamond pattern to line up evenly on both sides of the walkway, and our edge cuts to be triangles with three even sides. It took us several hours of shifting them around to get it right.
STEP 3: INSTALL EDGING
We lined our walkway with plastic paver edging. This prevents the pavers from shifting out of place. Once our grass fills in, we expect this to become less visible.
step 4: kill weeds + lay landscaping fabric
We pulled weeds from the two cracks in the walkway, and sprayed weed killer on for good measure. We laid landscaping fabric over the cracks, which will prevent weeds from growing and pushing pavers out of place.
STEP 5: Spread Paver sand over concrete
We had some trial & error in this step. We accidentally bought this paver base sand, which we assumed was what we should be using based on the description. We poured out a bunch of bags and stomped it down, attempting to create a solid base over our concrete.
We spread the finer paver sand on top of it, and started laying pavers. After getting through many rows, we tested them and realized they were wobbly. The paver base was too rocky, so we removed all of it and started from scratch.
This time, we skipped the paver base and used JUST sand. The finer sand was so much easier to work with and gave the pavers a soft but firm surface to sit on. We poured about 3/4″ of leveling paver sand on top of the old concrete and spread it to level out any minor surface imperfections.
STEP 6: lay pavers
We laid our pavers one by one based on the measurements we marked during our dry run. We used plastic paver spikes as spacers, placing one in each joint. When we were finished, we reused them for additional edging we installed around the yard.
Step 6: MAKE ALL OF YOUR CUTS
To make our cuts, we used a circular saw for straight cuts, and a grinder for our curved cuts. For both tools, we used diamond tip blades, which are needed for cutting through concrete and stone without chipping. Because we laid our pavers in a diamond pattern and had big curve in our pathway, we had to make a LOT of cuts. It took
us Bryan many hours to get through all of them, but it was worth it!
step 7: spread polymeric sand
Once all of the pavers were in place and our cuts were finished, we cleaned them off, removed the spacers, and spread polymeric sand into the joints. Polymeric sand is different from regular sand – it has polymers in it that become like a glue and hold pavers together when it gets wet.
We used a broom to sweep the sand into all of the joints, and then wet the entire walkway with our hose when we were finished.
I wasn’t sure just how secure our pavers would be, being that we didn’t use mortar, but this for sure worked. They haven’t shifted one bit, even with furniture moved in and out, the stroller going over them every day, etc.
step 8: Adjust stair treads and risers
By installing the 1.5″ pavers over our walkway, we needed to add height to our stair treads to level everything out. You can see here how short our bottom porch step is, and the unfinished edge in the front.
We bought limestone stair treads from a local stone yard to cap the front of the walkway and all of the stairs. It’s a little lighter than the concrete is, but over time it should even out. Next year, we’ll finish our stairs and add limestone risers, but for now, paint will get us through the winter!
We’re really, reaaaaaally happy with how it came out! We saved hundreds, if not thousands, by using these $1 pavers and working with what we had.
OUR RETAINING WALL
You may have also noticed that we installed a retaining wall! This was another budget friendly project that we tackled ourselves, and one that made a HUGE impact on our curb appeal. Remember when it looked like this?
This view looks justtt a bit different now.
We used these materials to get the project done:
After everything was dry, we went over the concrete with this travertine ledger stone, and used the same landscape adhesive to adhere it to the wall.
The nice thing about this ledger stone is that you don’t need grout, so it saved on time! We placed more $1 pavers on top to cap it off and tie it into the walkway.
This is what our house looks like now…
And this is where we started – eeeek. So glad we got these hardscaping projects finished before the weather turned!
That’s it guys. What do you think? Would you tackle a project like this?